Example: confidence

MBP6K208 MBP11K208 Installation and user manual

ENGLISH. HotSwap MBP. Maintenance Bypass MBP6K208 . MBP11K208 . Installation and user manual Copyright 2012 EATON. All rights reserved. Service and support: Call your local service representative SK-90610-Y4_EN. SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. This manual contains important instructions that should be followed during Installation and maintenance of the MBP and UPS. The Hotswap MBP models that are covered in this manual are intended for Installation in an environment within 0 to 40 C, free of conductive contaminant.

Page 2 SK-90610-Y4_EN Special symbols The following are examples of symbols used on the Hotswap MBP to alert you to important information: RISK OF ELECTRIC SHOCK - Observe the warning associated with the risk of electric shock symbol.

Tags:

  Information, Important, Important information

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Other abuse

Transcription of MBP6K208 MBP11K208 Installation and user manual

1 ENGLISH. HotSwap MBP. Maintenance Bypass MBP6K208 . MBP11K208 . Installation and user manual Copyright 2012 EATON. All rights reserved. Service and support: Call your local service representative SK-90610-Y4_EN. SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. This manual contains important instructions that should be followed during Installation and maintenance of the MBP and UPS. The Hotswap MBP models that are covered in this manual are intended for Installation in an environment within 0 to 40 C, free of conductive contaminant.

2 This equipment has been tested and found to comply with Class A UPS,pursuant to Part 15 of the FCC. Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual , may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

3 Certification standards (in use with UPS). pp Safety: IEC/EN 62040-1 / : 2008. UL 1778 4th edition pp EMC: IEC 62040-2 / : 2005. EN 62040-2 / : 2006. FCC part 15 Class A. pp Performance: IEC/EN 62040-3 / : 2011. pp IEC 61000-4-2 (ESD): level 3. pp IEC 61000-4-3 (Radiated field): level 3. pp IEC 61000-4-4 (EFT): level 4. pp IEC 61000-4-5 (Fast transients): level 4. pp IEC 61000-4-6 (Electromagnetic field): level 3. pp IEC 61000-4-8 (Conducted magnetic field): level 4. Special symbols The following are examples of symbols used on the Hotswap MBP to alert you to important information : RISK OF ELECTRIC SHOCK - Observe the warning associated with the risk of electric shock symbol.

4 important instructions that must always be followed. This symbol indicates that you should not discard waste electrical or electronic equipment (WEEE). in the trash. For proper disposal, contact your local recycling/reuse or hazardous waste center. information , advice, help. Refer to the user manual of UPS. Page 2 SK-90610-Y4_EN. SAFETY INSTRUCTIONS. ENGLISH. Safety of persons pp The system has its own power source when connected to the UPS (UPS battery). Consequently, the power outlets may be energized even if the system is disconnected from the AC power source.

5 Dangerous voltage levels are present within the system. It should be opened exclusively by qualified service personnel. pp The product must be properly grounded, always connect the earth wire first Product safety pp The MBP connection instructions and operation described in the manual must be followed in the indicated order. Disconnection and overcurrent protection devices shall be provided by others for AC in/out circuits. pp CAUTION - To reduce the risk of fire, the unit connects only to a circuit provided with branch circuit overcurrent protection (please refer to the UPS User manual for current rating), in accordance with the National Electric Code, ANSI/NFPA 70 (US installations only).

6 The upstream circuit breaker must be easily accessible. The unit can be disconnected from AC power source by opening this circuit breaker, and if still connected to UPS, by previously shutting down the UPS (refer to the UPS User manual ). pp Check that the indications on the rating plate correspond to your AC powered system and to the actual electrical consumption of all the equipment to be connected to the system. pp Never install the system near liquids or in an excessively damp environment. pp Never let a foreign body penetrate inside the system.

7 Pp Never expose the system to direct sunlight or source of heat. pp If the system must be stored prior to Installation , storage must be in a dry place. pp The admissible storage temperature range is -15 C to +60 C. Special precautions pp The Hotswap MBP is designed to work with approved EATON UPS (contact your Eaton reseller for more information ). pp All repairs and service should be performed by AUTHORIZED SERVICE PERSONNEL ONLY. There are NO USER SERVICEABLE PARTS inside the MBP. SK-90610-Y4_EN Page 3. Contents 1.

8 5. Environmental 2. 6. Standard Description / 3. 9. Inspecting the Unpacking the Checking the accessory Mechanical 10. Installation 10. 4. Power cables 11. 12. 5. 14. UPS start-up with HotSwap 14. UPS replacement with HotSwap 15. UPS maintenance with HotSwap 17. 6. 18. Page 4 SK-90610-Y4_EN. 1. Introduction ENGLISH. Thank you for selecting an EATON product to protect your electrical equipment. The HotSwap MBP range has been designed with the utmost care. We recommend that you take the time to read this manual to take full advantage of the many features of your MBP (Maintenance Bypass).

9 Before installing your HotSwap MBP with your UPS, please read first the safety instructions. Then follow the indications in this manual , which completes the UPS Installation and User manual . To discover the entire range of EATON products, we invite you to visit our web site at powerquality or contact your EATON representative. Environmental protection EATON has implemented an environmental-protection policy. Products are developed according to an eco-design approach. Substances This product does not contain CFCs, HCFCs or asbestos.

10 Packing To improve waste treatment and facilitate recycling, separate the various packing components. pp The cardboard we use comprises over 50% of recycled cardboard. pp Sacks and bags are made of polyethylene. pp Packing materials are recyclable and bear the appropriate identification symbol 01. PET. Materials Abbreviations Number in 01. the symbols PET. Polyethylene terephthalat PET 01. High-density polyethylene HDPE 02. Polyvinyl chloride PVC 03. Low-density polyethylene LDPE 04. Polypropylene PP 05. Polystyrene PS 06.


Related search queries